移印免烘烤不锈钢油墨

【性能检测】
1、3M胶带划百格测试：无脱落
2、耐冲压测试：1mm厚铝板180°折弯无变化。
3、耐酒精测试：用脱脂棉沾浓度99%工业酒精以500G力水平来回200次无脱色。
【注意事项】
1、先小量试印确认符合要求后再批量生产。
2、做好承印物的表面清除油脂及杂质工作，以促进附着效果。
3、附着力、硬度、耐酸性、耐酒精性、耐化学品性、抗划伤性、耐磨性等性能的检测，
需要完全固化后方可检测。
4、未经允许情况下，不得将本系列油墨与其它类型油墨混用及配色。
5、油墨，稀释剂使用及储存时严禁烟火。
6、使用时注意施工场所的通风状况良好，尽量避免**直接接触。
7、本品不慎溅入口、鼻、眼、耳内，应用大量水清洗或直接求助医生。
8、技术参考数见下表：
检验项目 检验结果 测试条件 
油墨线度 ≤12um 刮板细度计 
干膜光泽 ≥65° 60°镜面光泽计 
干燥速度 表干 25℃×5-10min 或60℃×2-3min 
实干 25℃12Hr或60℃×10min 
耐酒精性 无变化 500克力/cm2酒精棉200次来回 
附着力 100/100 1mm×1mm×100格3M胶纸剥离 
耐酸性 无变化 浸泡5%HCI×24Hr 
耐碱性 无变化 浸泡5%NaOH×24Hr 
耐盐性 无变化 浸泡5%NaCI×24Hr 
耐水性 无变化 浸泡20℃自来水×96Hr 
耐磨性 不见底 500克/cm2负载含砂橡皮200来回 
耐热性 无变化 80℃×12Hr 
The products are mainly used in screen printing and theprinting of various kinds of metal, glass, vacuum plating,electroplating, electrophoresis, water anodic alumina, electrolyticplate, aluminum plate, plastic spraying, dusting, electrostaticspray painting, paint surface and various ceiling oxide board,mirror panels, coated board, roller coated board and otherproducts.
2, product characteristics: light, good adhesion, fastdrying, stamping resistance.
3, diluent: with our B-03 special thinner or 783 open oil,washing network water cleaning screen with 718.
4, curing agent: one component use, can also choose to addour JS-10 special curing agent is used to increase the ink adhesionand physical and chemical resistance.
5, printing ink allocation methods: open cans to stir well,take appropriate amount needed to dilute ink printing viscosity. Ifyou need to add curing agent, first add curing agent after mixingand set aside for 10 minutes, and curing agent for ink completelycrosslinking after dilution.
6, the drying time: dry, dry time table for 5-10 minutes,work time within 24 hours, 80 degrees bake for 20 minutes can bedried quickly.
7, adding curing agent after the use of time: 4-6 hours,expired please abandoned, residual ink Unrecyclable.
[detection] performance
1, 3M tape row adhesion test: withoutshedding
2, stamping resistance test: 1mm thick aluminum 180 degreebend without change.
3, alcohol resistant test: with cotton dipped in 99% alcoholconcentration of industry to 500G stress level and back 200 timeswithout decolorization.
[note]
1, the first small try printing again after confirmation ofcompliance with the requirements of mass production.
2, do a good job in the substrate surface to remove greaseand impurities, in order to promote the adhesion effect.
Detection of 3, adhesion, hardness, acid resistance, alcoholresistance, chemical resistance, scratch resistance, abrasionresistance and other properties,
Fully cured before detection.
4, without permission, may not use the series of ink andother types of ink mixing and matching.
5, ink, fireworks is strictly prohibited the use of thinnerand storage.
6, the use of ventilation conditions attention theconstruction site is good, try to avoid direct contact withskin.
7, this product is inadvertently splashed entrance, nose,eyes, ears, use a large number of water washing or direct helpdoctor.