移印PE油墨，PE移印油墨

　油墨特性：拥有和德国彩丽宝一样的颜色，主要用于PP、PE、BOPP等材料上，具有高色泽、高色彩、高遮盖力、高稳定性、耐酒精及耐磨擦之特点。　　印刷：丝印移印均可。 　　表干及实干时间：表干时间自然挥发5-10分钟；实干时间在24小时以内。　　稀释及清洗：SV3慢干开油水、UVK1（移印开油水）可使用718洗网水清洗。 　　 　　测试方法（完全干燥后）：　　1、3m胶纸粘在画有百格的油墨表面，45度角迅速拉起不脱油；　　2、纯度99%的工业酒精，一千克砝码用棉布包住在油墨表面，以水平力来回拉200次无脱色；　　3、耐磨：橡皮擦500g力水平来回擦500次。 　　 　　使用方法： 　　1、使用前应充分搅拌，用后随时封闭；　　2、搅拌时加开油水10-15%，稀释到印刷粘度； 　　3、网板塞网时可用洗网水清洗； 　　4、不得与其它类型油墨混合使用。 　　　　注意事项： 　　1、塑胶材料的外观相似，但可能会是不同的材料，客户需试印确定其符合要求后，再批量印刷；　　2、在移印过程中，如出现拉丝或散开，可适当加入一些慢干膏即可； 　　3、环境温度过高，将会影响油墨原有质量；　　4、根据气候变化，请远离火源，阴暗环境下存放。 5、技术参考数见下表： 检验项目 检验结果 测试条件 油墨线度 ≤12um刮板细度计 干膜光泽 ≥65° 60°镜面光泽计 干燥速度 表干 25℃×5-10min 或60℃×2-3min 实干25℃12Hr或60℃×10min 耐酒精性 无变化 500克力/cm2酒精棉200次来回 附着力 100/1001mm×1mm×100格3M胶纸剥离 耐酸性 无变化 浸泡5%HCI×24Hr 耐碱性 无变化 浸泡5%NaOH×24Hr 耐盐性无变化 浸泡5%NaCI×24Hr 耐水性 无变化 浸泡20℃自来水×96Hr 耐磨性 不见底 500克/cm2负载含砂橡皮200来回耐热性 无变化 80℃×12Hr Ink characteristics: have and Germany Cailitreasure the same color, is mainly used for PP, PE, BOPP and othermaterials, with a high color, high color, high covering power,alcohol resistant and wear resistance, high stability. Printing:silk screen printing can be. Table dry and work time: surface drytime natural volatile 5-10 minutes; work time within 24 hours.Dilution and cleaning: SV3 slow dry open water, UVK1(printing openwater) also can use 718 washing network water cleaning. Test method(completely dry): 1, 3M adhesive tape sticky ink surface adhesionin painting,45 degree angle quickly pulled off the oil; 2, purity99% of industrial alcohol, using cotton bag in the surface of theink one kilogram weight to horizontal force and pull 200 timeswithout decolorization; 3, wear: the eraser 500g force level wipe500 times back and forth. Method of use: 1, before the use shouldbe fully mixing, use at any time after the closure; 2, mixing anadditional 10-15% in oil and water, diluted to printing viscosity;3, mesh plug mesh can be used when washing network water cleaning;4, shall not be mixed with other types of ink. The matters needingattention: 1, the plastic material of similar appearance, but maybe of different materials, customers need to try to determine itsrequirements, and then bulk printing; 2, in the printing process,such as drawing or spread out,may be appropriate to add some slowdry paste can be; 3, the ambient temperature is too high, it willaffect the quality of the original ink; 4, according to the climatechange, please stay away from fire, stored in darkenvironment.