丝印PE保护膜油墨
油墨特性：拥有和德国彩丽宝一样的颜色，主要用于PP、PE、BOPP等材料上，具有高色泽、高色彩、高遮盖力、高稳定性、耐酒精及耐磨擦之特点。
印刷：丝印移印均可。
表干及实干时间：表干时间自然挥发5-10分钟；实干时间在24小时以内。
稀释及清洗：SV3慢干开油水、UVK1（移印开油水）同时可使用718洗网水清洗。
测试方法（完全干燥后）：
1、3m胶纸粘在画有百格的油墨表面，45度角迅速拉起不脱油；
2、纯度99%的工业酒精，一千克砝码用棉布包住在油墨表面，以水平力来回拉200次无脱色；
3、耐磨：橡皮擦500g力水平来回擦500次。
使用方法：
1、使用前应充分搅拌，用后随时封闭；
2、搅拌时加开油水10-15%，稀释到印刷粘度；
3、网板塞网时可用洗网水清洗；
4、不得与其它类型油墨混合使用。
注意事项：
1、塑胶材料的外观相似，但可能会是不同的材料，客户需试印确定其符合要求后，再批量印刷；
2、在移印过程中，如出现拉丝或散开，可适当加入一些慢干膏即可；
3、环境温度过高，将会影响油墨原有质量；
4、根据气候变化，请远离火源，阴暗环境下存放。
5、技术参考数见下表：
检验项目 检验结果 测试条件
油墨线度 ≤12um 刮板细度计
干膜光泽 ≥65° 60°镜面光泽计
干燥速度 表干 25℃×5-10min或60℃×2-3min
实干 25℃12Hr或60℃×10min
耐酒精性 无变化500克力/cm2酒精棉200次来回
附着力 100/1001mm×1mm×100格3M胶纸剥离
耐酸性 无变化 浸泡5%HCI×24Hr
耐碱性 无变化浸泡5%NaOH×24Hr
耐盐性 无变化浸泡5%NaCI×24Hr
耐水性 无变化浸泡20℃自来水×96Hr
耐磨性 不见底500克/cm2负载含砂橡皮200来回
耐热性 无变化 80℃×12Hr
Ink characteristics: have and Germany Caili treasure the samecolor, is mainly used for PP, PE, BOPP and other materials, with ahigh color, high color, high covering power, alcohol resistant andwear resistance, high stability.
Printing: silk screen printing can be.
Table dry and work time: surface dry time natural volatile 5-10minutes; work time within 24 hours.
Dilution and cleaning: SV3 slow dry open water, UVK1(printing openwater) also can use 718 washing network water cleaning.
Test method (completely dry):
1, 3M adhesive tape sticky ink surface adhesion in painting,45degree angle pulled off the oil;
2, purity 99% of industrial alcohol, using cotton bag in thesurface of the ink one kilogram weight to horizontal force and pull200 times without decolorization;
3, wear: the eraser 500g force level wipe 500 times back andforth.
Method of use:
1, before the use should be fully mixing, use at any time after theclosure;
2, mixing an additional 10-15% in oil and water, diluted toprinting viscosity;
3, mesh plug mesh can be used when washing network watercleaning;
4, shall not be mixed with other tyPES of ink.
The matters needing attention:
1, the plastic material of similar appearance, but may be ofdifferent materials, customers need to try to determine itsre, and then bulk printing;
2, in the printing process, such as drawing or spread out,may beappropriate to add some slow dry paste can be;
3, the ambient temperature is too high, it will affect the the original ink;
4, according to the climate change, please stay away from fire,stored in dark environment.
