產品特性：防酒精佳；高光澤、高硬度耐變黃；附著力超強；低氣環保；耐腐蝕、卡怪酸堿、耐汽油；
表面處理：被塗物表面應徹底清潔、幹凈、幹燥。
塗裝方式：絲印、移印、噴塗。
使用註意事項：
1.刷塗時確保工作場所通風良好。
2.做好個人和地板的保護措施，防止漆膜沾汙。
3.放置於兒童接觸不到的地方。
性能檢測：
用3M600膠帶劃百格測試無脫落；
用棉布沾95%工業酒精以500G力水平來回擦拭100次無脫色；
1mm厚鋁片在印刷位置進行沖斷、卷邊、延壓後邊緣位置無脫落；
包裝規格：1KG/膠罐，12罐/箱。
儲存條件：置於幹燥通風處常溫保存；避免高溫、太陽直射，嚴禁煙火。
註意事項：請向我司索取《MSDS安全使用手冊》，並按指引進行安全生產。
註意事項：
1、先小量試印確認符合要求後再批量生產。
2、多色套印時，需表幹後才能進行下壹顏色印刷。
3、附著力、硬度、耐酒精性、耐化學品性、抗劃傷性、耐磨性等性能的檢測，需要待墨層完全固化後方可檢測。
4、不得將本系列油墨與其它類型油墨混用或配色。
5、註意作業車間的濕度，濕度過大會影響附著力，濕度過小會容易拉絲，溫度高容易堵網。
6、油墨、稀釋劑使用及儲存時嚴禁煙火並放置於陰涼處。
7、每次取出足夠使用量油墨後，須及時蓋好油墨蓋，否則影響保證期（壹般情況下保證期為1年）。
8、未用完之油墨不可隨便倒回未經稀釋的油墨罐，以免有色差等不良出現。
9、盡量避免皮膚直接接觸，過敏者使用前應塗覆壹層皮膚護膚膏或戴不滲透手套。註意接觸油墨過程不要讓油墨飛濺到眼、耳、口、鼻或身上。
Product characteristics: good anti alcohol; high gloss, highhardness yellowing; super low adhesion; environmental protection;corrosion resistance, acid and alkali resistance, gasolinechair;
Surface treatment: the surface of the coated material should bethoroughly clean, clean and dry.
Coating methods: silk printing, printing, spraying.
Use note:
1. to ensure that the workplace is well ventilated when the brushis painted.
2. do a good job of personal and floor protection measures toprevent fouling of the film.
3. are placed in places where children are not in contact.
Performance detection:
Use 3M600 tape to make 100 lattice tests without fallingoff.
With cotton cloth, 95% industrial alcohol was wiped back and forthat the level of 500G force for 100 times withoutdecolorization.
The position of 1mm thick aluminum sheet in the printing positionis broken, curling, and the edge position after the pressure is without falling off.
Package specifications: 1KG/ glue cans, 12 cans / boxes.
Storage conditions: keep at room temperature in the dry andventilated place; avoid high temperature, direct sunlight, andstrictly prohibit fireworks.
Note: please take the "MSDS safety manual" to our department andmake safe production according to the guidelines.
Matters needing attention：
1, the first small test print confirms that it meets therequirements and then batch production.
2, polychromatic printing, the need to dry after the next colorprinting.
3, adhesion, hardness, alcohol resistance, chemical resistance,scratch resistance, wear resistance and other performance testing,need to be completely cured behind the ink layer can bedetected.
4. The inks of this series shall not be mixed with or matched withother types of ink.
5, pay attention to the humidity of the workshops, humidity overthe assembly influence adhesion, humidity too small will easilypull wire, the temperature is high, easy to block the net.
6. The use and storage of inks and diluents is strictly prohibitedand placed in the shade.
7. The ink cover must be covered in time after the sufficientamount of ink is taken out, otherwise the guarantee period will beaffected (in general, the guarantee period is 1 years).
8, the unused ink can not be casually back without dilution of theink tank, in order to avoid color and other adverse.
9, try to avoid direct contact of the skin, the allergy should becoated with skin cream or wear glove before use. Be careful not tosplash the ink onto the eye, ear, mouth, nose, or body by touchingthe ink.
