EXM628F01进口原装PCB

EXM628F01进口原装PCB

EXM628F01全新原装、EXM628F01在线报价

Intrinsically-safe, industrial,quartz shear ICP® accel., 100 mV/g, 0.3 to 12k Hz, top exit, 2-pinconn., frequency sweep ISO 17025 accredited calibration

Sensitivity: (±5%) 100 mV/g (10.2 mV/(m/s²))

Frequency Range: (±3dB) 20 to 720000 cpm (0.33 to 12000 Hz)

Sensing Element: Quartz

Measurement Range: ±50 g (±490 m/s²)

Weight: 3.3 oz (94 gm)

PERFORMANCESensitivity (±5 %)100 mV/g10.2mV/(m/s²)[1] Measurement Range±50 g±490 m/s²
Frequency Range (±5 %)60 to 240000 cpm1 to 4000Hz[3] Frequency Range (±10 %)40 to 390000 cpm0.67 to 6500Hz
Frequency Range (±3 dB)20 to 720000 cpm0.33 to 12000 Hz
Resonant Frequency1080 kcpm18 kHz[4] Broadband Resolution (1to 10000 Hz)1000 µg9810µm/sec2[4] Non-Linearity±1 %±1%[2] Transverse Sensitivity≤5 %≤5 %
ENVIRONMENTALOverload Limit (Shock)5000 g pk49050 m/s² pk
Temperature Range-65 to +250 °F-54 to +121 °C
Temperature ResponseSee Graph %/°FSee Graph %/°F[4] EnclosureRatingIP68IP68
ELECTRICALSettling Time (within 1% of bias)≤10 sec≤10 sec
Discharge Time Constant≥0.5 sec≥0.5 sec
Excitation Voltage18 to 28 VDC18 to 28 VDC
Constant Current Excitation2 to 20 mA2 to 20 mA
Output Impedance<100 Ohm<100 Ohm
Output Bias Voltage8 to 12 VDC8 to 12 VDC
Spectral Noise (10 Hz)50 µg/√Hz491(µm/sec2)/√Hz[4] Spectral Noise (100 Hz)20µg/√Hz196 (µm/sec2)/√Hz[4] Spectral Noise (1kHz)6 µg/√Hz59 (µm/sec2)/√Hz[4] ElectricalProtectionRFI/ESDRFI/ESD
Electrical Isolation (Case)>100000000 Ohm>100000000 Ohm
PHYSICALSize - Hex7/8 in22 mm
Size - Height2.06 in52.3 mm
Weight3.3 oz94 gm
Mounting Thread1/4-28 FemaleNot Applicable[5] Mounting Torque2to 5 ft-lb2.7 to 6.8 Nm
Sensing ElementQuartzQuartz
Sensing GeometryShearShear
Housing MaterialStainless SteelStainless Steel
SealingWelded HermeticWelded Hermetic
Electrical Connector2-Pin MIL-C-50152-Pin MIL-C-5015
Electrical Connection PositionTopTop

All specifications are at room temperature unless otherwisespecified.

Product Notes

[1] Conversion Factor 1g = 9.81 m/s².
[2] Zero-based, least-squares, straight line method.
[3] The high frequency tolerance is accurate within ±10% of thespecified frequency.
[4] Typical.
[5] 1/4-28 has no equivalent in S.I. units.
[6] See PCB Declaration of Conformance PS023 or PS061 fordetails.

Accessories:

Supplied081A40Mounting Stud(1)
ICS-1NIST-traceable single-axis amplitude response calibration from600 cpm (10 Hz) to upper 5% frequency(1)

Optional Versions:

(CS) Canadian Standards Association Approved IntrinsicallySafe

ENGLISHSI    Hazardous Area ApprovalCl I, DivI, Groups A, B, C, D; Cl II, Div I, Groups E, F, G; Cl III, DivI    Hazardous Area ApprovalEx ia IIC T4, AExiaIIC, T4    Hazardous Area ApprovalCl I, Div 2,Groups A, B, C, D; ExnL IIC T4, AExnA IIC T4

(EX) Hazardous Area Approval- contact factory for specificapprovals

ENGLISHSI    Hazardous Area ApprovalEEx ia IICT4, -54°C<=Ta<=121°C, II 1 G

(LB) Low Bias Voltage

ENGLISHSI    Output Bias Voltage6 to 8VDC    Excitation Voltage12 to 28VDC    Measurement Range±35 g±343 m/s²

(M) Metric Mount

ENGLISHSI
Accessories:
M081A61Mounting Stud(1)

052 cable, 10-ft,environmentally sealed MIL-type, 2-socket conn. to blunt cuttermination

Two-conductor shielded twistedpair cable with polyurethane jacket, 10 ft., push-on 2-socket MILwith environmental boot to blunt cut