EX603C01单价很好
Intrinsically safe approved general purpose industrial ceramicshear ICP® accel, 100 mV/g, 0.5 to 10K Hz, top exit, 2-pin conn.,single point ISO 17025 accredited calibration
Sensitivity: (±10%) 100 mV/g(10.2 mV/(m/s²))
Frequency Range: (±3dB) 30 to 600000 cpm(0.5 to 10000 Hz)
Sensing Element: Ceramic
Measurement Range: ±50 g(±490 m/s²)
Weight: 1.8 oz(51 gm)
All specifications are at room temperature unless otherwisespecified.
ProductNotes
[1] Conversion Factor 1g = 9.81 m/s².
[2] Zero-based, least-squares, straight line method.
[3] The high frequency tolerance is accurate within ±10% of thespecified fre
[4] Typical.
[5] 1/4-28 has no e in S.I. units.
[6] See PCB Declaration of Conformance PS023 or PS060 fordetails.
Accessories:
Supplied | |||
081A40 | Mounting Stud | (1) | |
ICS-2 | NIST-traceable single-pointamplitude response calibration at 6000 cpm (100 Hz) for eachaxis | (1) |
OptionalVersions:
(M) Metric Mount
ENGLISH | SI |
Accessories: | |||
M081A61 | Mounting Stud | (1) |
English: | SI: | ||
---|---|---|---|
Performance | |||
Sensitivity (±10 %) | 100 mV/g | 10.2 mV/(m/s²) | [1] |
Measurement Range | ±50 g | ±490 m/s² | |
Frequency Range (±3 dB) | 30 to 600000 cpm | 0.5 to 10000 Hz | [3] |
Resonant Frequency | 1500 kcpm | 25 kHz | [4] |
Broadband Resolution (1 to 10000 Hz) | 350 µg | 3434 µm/sec2 | [4] |
Non-Linearity | ±1 % | ±1 % | [2] |
Transverse Sensitivity | ≤7 % | ≤7 % | |
Environmental | |||
Overload Limit (Shock) | 5000 g pk | 49050 m/s² pk | |
Temperature Range | -65 to +250 °F | -54 to +121 °C | |
Temperature Response | See Graph %/°F | See Graph %/°F | [4] |
Enclosure Rating | IP68 | IP68 | |
Hazardous Area Approval | Cl I, Div 2, Groups A, B, C, D; ExnL IIC T4, AExnA IIC T4 | Cl I, Div 2, Groups A, B, C, D; ExnL IIC T4, AExnA IIC T4 | |
Hazardous Area Approval | EEx nL IIC T4, -40°C<=Ta<=121°C, II 1 G | EEx nL IIC T4, -40°C<=Ta<=121°C, II 1 G | |
Hazardous Area Approval | Cl I, Div I, Groups A, B, C, D; Cl II, Div I, Groups E, F, G;Cl III, Div I | Cl I, Div I, Groups A, B, C, D; Cl II, Div I, Groups E, F, G;Cl III, Div I | |
Hazardous Area Approval | Ex ia IIC T4, AExia IIC, T4 | Ex ia IIC T4, AExia IIC, T4 | |
Hazardous Area Approval | EEx nL IIC T4, -40°C<=Ta<=121°C, II 3 G | EEx nL IIC T4, -40°C<=Ta<=121°C, II 3 G | |
Electrical | |||
Settling Time (within 1% of bias) | ≤2.0 sec | ≤2.0 sec | |
Discharge Time Constant | ≥0.3 sec | ≥0.3 sec | |
Excitation Voltage | 18 to 28 VDC | 18 to 28 VDC | |
Constant Current Excitation | 2 to 20 mA | 2 to 20 mA | |
Output Impedance | <150 Ohm | <150 Ohm | |
Output Bias Voltage | 8 to 12 VDC | 8 to 12 VDC | |
Spectral Noise (10 Hz) | 8 µg/√Hz | 78.5 (µm/sec2)/√Hz | [4] |
Spectral Noise (100 Hz) | 5 µg/√Hz | 49.1 (µm/sec2)/√Hz | [4] |
Spectral Noise (1 kHz) | 4 µg/√Hz | 39.2 (µm/sec2)/√Hz | [4] |
Electrical Isolation (Case) | >100000000 Ohm | >100000000 Ohm | |
Physical | |||
Size - Hex | 11/16 in | 18 mm | |
Size - Height | 1.65 in | 42.2 mm | |
Weight | 1.8 oz | 51 gm | |
Mounting Thread | 1/4-28 Female | No Metric E | [5] |
Mounting Torque | 2 to 5 ft-lb | 2.7 to 6.8 Nm | |
Sensing Element | Ceramic | Ceramic | |
Sensing Geometry | Shear | Shear | |
Housing Material | Stainless Steel | Stainless Steel | |
Sealing | Welded Hermetic | Welded Hermetic | |
Electrical Connector | 2-Pin MIL-C-5015 | 2-Pin MIL-C-5015 | |
Electrical Connection Position | Top | Top |